AC repair
Furnace & heating
Heat pumps
Ductless mini splits
Carrier
Trane
GoodmanSeasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Get your free estimateTrusted Furnace Repair for Glendale Homeowners
When the heat stops on a cold Glendale night, the fix is usually smaller than the fear. Furnace repair in Glendale typically runs $150 – $700, and most problems trace back to a worn igniter, a dirty flame sensor, or a blower that’s seen too many summers. Our technicians have up to experience on Carrier, Trane, and Bryant systems, plus a strong local reputation for honest diagnostics. We don’t guess at your system; we test it. We answer 24/7, with fast dispatch from 7am to 7pm, so you get a real plan the same day you call. One call to (855) 473-8857 starts it.
Furnace Maintenance
Furnace Maintenance is the seasonal check that catches small problems before they strand your system in the middle of a cold snap, and we recommend it once a year, ideally before you start leaning on the heat. It covers the burners, the heat exchanger, the flame sensor, the blower, and the filter, plus a check of venting and safety controls. Jasper AC Repair handles this for residential systems from all nine major brands, so whatever’s in your closet or garage, we know it. Cost is modest, usually well within the same range as a small repair, and a written report tells you exactly what we found and what, if anything, needs fixing. Our technicians aren’t paid on what they sell, so the report reflects the system, not a sales target.
What a Seasonal Check Covers
We pull the panels, inspect the burners and heat exchanger, test the igniter, and confirm the blower moves the air it should. Filters and flame sensors get cleaned or replaced when they’re clearly past their useful life. You leave with a short list of what’s healthy and what to watch.
When to Book It
Fall is the natural time, before the first real cold evening, but a system that’s been sitting for a year benefits from a check at any point. If you’ve noticed short cycling or uneven heat, book it sooner rather than later.
Styles & brands we work with
- AC repair
- Furnace & heating
- Heat pumps
- Ductless mini splits
- Carrier
- Trane
- Goodman
Heat Pump Repair
Heat Pump Repair addresses the system that both heats and cools, and when it fails it can fail on either side, which is why diagnosis matters. You need it when the unit runs constantly, blows lukewarm air in heat mode, or trips the breaker, and you need it before the problem compounds. Jasper AC Repair services heat pumps from the same nine manufacturers we cover elsewhere, including Carrier and American Standard, so you’re not hunting for a specialist. Typical estimates for heat pump repair in Glendale land in the $150 – $700 range, and the written estimate sets the final price. Because a heat pump leans on reversing valves, defrost controls, and refrigerant charge, we check the whole cycle rather than one component.
Heating and Cooling From One Unit
A heat pump moves heat rather than making it, so a failing reversing valve can cool when you want heat. We test the valve, the defrost board, and the charge together. One fix usually restores both seasons.
When It Stops Switching Modes
If your system cools in heating season or heats when you want cooling, the problem is usually in the reversing valve or its control. That’s a job for a trained technician, not a homeowner reset. We diagnose it and quote the fix.
Heating Repair
Heating Repair covers the whole family of residential heating equipment, from gas furnaces to heat pumps to boilers, and we recommend it the moment your home stops holding temperature. Common triggers are a furnace that runs but never warms the house, a pilot or ignition that won’t light, or a blower that’s gone quiet. Jasper AC Repair handles all three of these systems under one roof, so you don’t hand off to a second contractor mid-problem. Estimates for heating repair in Glendale typically fall between $150 and $700, depending on the part and the access, and the written estimate locks in the price before we start. We service nine major HVAC brands, so the make of your equipment doesn’t matter to us.
Mild Winters, Real Problems
Glendale winters stay mild, but that doesn’t protect a system that ran hard all summer. Bearings, belts, and control boards still wear out, and a system that won’t heat is a comfort problem regardless of the forecast. We treat it like one.
Why We Check Before We Replace
Plenty of heating problems are one part away from solved. We test before recommending a replacement, because patching a sound system is cheaper than swapping it. When replacement genuinely makes more sense, we say so plainly.
Boiler Repair
Boiler Repair keeps a hydronic heating system running, and it’s the right call when radiators stay cold, the boiler short cycles, or you hear knocking in the pipes. Boilers are less common in Southern California than furnaces, but they turn up in older Glendale homes, and they need a technician who understands pressure, water level, and circulation. Jasper AC Repair diagnoses and repairs boiler systems as part of our residential heating work, and we’re honest when a boiler has reached the end of its useful life. Repair estimates generally land in the $150 – $700 range, and the written estimate sets the final price.
Pressure and Water Level
A boiler running low on water or high on pressure will shut down or, worse, fail a safety limit. We check both, plus the expansion tank and relief valve. These are the checks that keep the system safe as well as warm.
Cold Radiators and Knocking Pipes
Cold radiators usually mean trapped air or a circulation problem, and knocking points to water hammer or a failing circulator. Both are diagnosable. We trace the cause before quoting the fix.
Gas Furnace Repair
Gas Furnace Repair deals with the most common heating system in Glendale homes, and it’s the one where safety matters most. You need it when you smell gas, hear the igniter click without ignition, see a yellow rather than blue flame, or notice soot around the unit. Gas lines and combustion are not a DIY repair, and we want to be direct about that: a trained technician should handle anything involving the gas valve, the burners, or the heat exchanger. Jasper AC Repair tests combustion, checks for carbon monoxide risk, and replaces failed components. Repair estimates here typically run $150 – $700, and the written estimate sets the price.
Reading the Flame
A steady blue flame with a clean, soft roar is what you want. A yellow, lazy, or lifting flame signals a combustion problem. We test for it and address it before it becomes a safety issue.
Igniters and Flame Sensors
The most common gas furnace failure is a dirty flame sensor or a worn igniter. Both are small, replaceable parts, and both are exactly the kind of fix a trained technician handles quickly. We stock nothing on a truck, so we quote and return with the right part.
Furnace Tune Up
Furnace Tune Up is the flat-price visit that keeps your system efficient and catches problems early, and it’s best done once a year before heating season. It’s a cleaning and inspection visit, not a repair, and it’s the cheapest way to extend the life of your equipment. Jasper AC Repair handles tune-ups for all nine major brands, and our technicians aren’t paid on what they sell, so you get a straight report of what they actually found. A typical tune-up estimate in Glendale runs $80 – $200, with the written estimate setting the final price. If the tune-up turns up a repair, we quote it before touching anything, and you decide.
What Gets Cleaned and Tested
Burners get cleaned, the flame sensor gets wiped or replaced, filters get swapped, and the blower and venting get checked. We also test the igniter and confirm the system shuts off safely. The flat price covers the visit, not a sliding scale.
The Written Report
After the visit, you get a short written report: what we found, what’s healthy, what to watch. There’s no upsell attached. The point is knowing the state of your system, not buying a bundle.
Emergency Furnace Repair
Emergency Furnace Repair is for the nights your heat quits and the house gets genuinely cold, and it’s the reason we staff a real phone line. You need it when the furnace stops entirely during cold weather, when there’s a gas smell, or when a CO alarm goes off. Jasper AC Repair answers the phone 24/7, with fast dispatch from 7am to 7pm. We don’t promise a middle-of-the-night fever pitch, but we do book emergency work into the next dispatch opening so you’re not waiting a week. Emergency repairs are quoted the same way as any other, typically $150 – $700, and nothing is billed above the written estimate for the same job. Call (855) 473-8857.
When It’s Truly an Emergency
A gas smell, a CO alarm, or no heat at all during a cold stretch are the real emergencies. Those get priority. A system that’s merely noisy or short-cycling is worth booking, just not on an emergency footing.
Safety First if You Smell Gas
If you smell gas, get everyone out of the house, don’t flip any switches, and call from outside. Then call us or your gas utility. A gas leak is a safety issue, not a repair ticket.
Brands We Service
We service Carrier equipment and know where it typically wears out, from inducer motors to the control board. We service Trane systems and understand how their cabinet layouts and controls behave in real homes. We service Bryant units, which share much of the same engineering family as Carrier and respond to the same diagnostic approach. We service American Standard equipment and can trace its common failures, from flame sensors to pressure switches. Because we’re brand-neutral, none of that knowledge is tied to a sales quota.
We also service Lennox, Goodman, Rheem, York, and Daikin systems across the same nine-brand set. That means you’ll never hear “we don’t service that unit” from us. Our technicians have up to experience across these makes, and we quote from what your system actually needs. Whether you have Bryant, American Standard, or any other make, we can help.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- No heat at all. The furnace runs but the house stays cold, or the system won’t start. This usually points to an ignition or control problem, and it’s worth a same-day call.
- A yellow or orange flame. Combustion that isn’t clean blue can mean carbon monoxide risk. Stop using the system and call us.
- Repeated cycling. Short cycling wears parts and wastes energy. It’s usually a sensor, a thermostat, or an airflow problem, and it’s fixable.
- Strange smells. A burning smell on first startup is often dust; a persistent smell or a gas odor is not. Gas odor means call before you do anything else.
- Loud banging or rattling. New noises usually mean a loose component or a failing blower. Catch it early and it’s a small repair; wait and it grows.
Our Process, Step by Step
- 1
We take the call and log your system. You tell us the make, the symptoms, and the age. We book you into the next available slot and confirm with a call.
- 2
We diagnose before we quote. A trained technician tests the ignition, the flame sensor, airflow, and the control board, using a combustion analyzer for gas equipment and a multimeter for electrical checks.
- 3
We explain what we found in plain words. No jargon dump, no scare tactics. You hear what failed, why, and what the options are.
- 4
We hand you a written estimate. The price is set per job, and the written estimate is what we bill. You approve it before any work starts.
- 5
We repair and test. Once the repair is done, we re-start the system, confirm the fix, and check that it cycles normally. If a replacement makes more sense than a repair, we say so and quote it.
How Much Does Furnace Repair Cost in Glendale?
Furnace repair in Glendale typically falls between $150 and $700, depending on the part that failed and how easy it is to reach. A typical igniter or flame sensor replacement sits at the low end of that range, since it’s a small part and a quick fix. A blower motor or control board replacement climbs toward the middle and top of the range because the part costs more and the labor takes longer. A gas valve or heat exchanger repair can push toward the upper end, and when a repair approaches the cost of a replacement, we tell you plainly so you can weigh the options instead of guessing.
Several things move the price: the brand and model of your system, the age of the equipment, and access to the unit. A furnace tucked into a tight closet takes longer than one with room to work. What doesn’t move the price is when you call; we don’t add a premium for a same-day or emergency job, and the written estimate sets the final number in every case.
To avoid overpaying, ask for the written estimate before any work begins, ask what the diagnostic turned up, and don’t accept a “we’ll see” price. A free estimate means exactly that: no charge to look and quote. Where the estimate is genuinely free, we say so up front, and there’s no obligation to accept the quote. When the honest answer is a full furnace replacement rather than a repair, we’ll quote that too, so you can compare the two in writing. Cooling and heating, handled under one company, means you don’t have to call a second contractor to get the full picture.
Our Service Area Near Glendale
We serve Glendale and the surrounding foothill and San Gabriel Valley communities, including La Cañada Flintridge, La Crescenta-Montrose, Altadena, South Pasadena, San Marino, Alhambra, West Hollywood, San Gabriel, and East San Gabriel. Response is typically same-day when you call during dispatch hours, and we schedule our work from 7am to 7pm, Sunday through Friday. If you’re in La Cañada Flintridge and need furnace repair, we cover that area too, and our furnace repair work extends through La Crescenta-Montrose. For the broader picture of our residential HVAC services, see Jasper AC Repair.
Serving Glendale, CA – Our Local Coverage Area
We serve Glendale and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Furnace Repair in Glendale
Furnace repair is the diagnosis and fix of a gas or electric heating system that isn’t working correctly. It covers parts like igniters, flame sensors, blower motors, control boards, and gas valves. A trained technician tests the system, identifies the failed component, and replaces or repairs it. In Glendale, most repairs we see are small-part failures, not full system failures. Call (855) 473-8857 for an exact quote, because estimates are free.
Most common furnace repairs finish in one visit, often within an hour or two once the right part is on hand. Some jobs require a part order, which pushes the fix to a follow-up visit. Complex issues, like a heat exchanger or a control board swap, can take longer. We confirm timing when we quote. Call to book.
Furnace repair in Glendale typically ranges from $150 to $700, depending on the part and the labor. Igniters and sensors sit at the low end, while blower motors and control boards run higher. The written estimate sets the final price, and the estimate itself is free. Call (855) 473-8857 for an exact quote.
Yes. We service Carrier equipment, along with Trane, Bryant, American Standard, and five other major brands. Our technicians have up to experience across these makes. Carrier systems tend to share controls and layout with the Bryant family, which helps diagnosis. Whatever brand you have, we can help.
Yes, we offer same-day service when you call during dispatch hours. We answer 24/7, and dispatch runs 7am-7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening. Call (855) 473-8857 to schedule.
We stand behind the work and can discuss warranty details on the specific repair when you call. Parts carry their manufacturer’s warranty, and labor is covered by our own. Ask about the warranty when you book so you know exactly what’s included. Call for details.
Clear access to the furnace, note the symptoms, and have the model number ready if you can find it. Make sure someone is home during the window, and keep pets in another room. If there’s a gas smell, leave the house first and call from outside.
Schedule Your Furnace Repair Service in Glendale Today
Don’t let a cold house wait on a maybe. Call (855) 473-8857 and we’ll book your furnace repair in Glendale with a trained technician who knows your brand. We answer 24/7, dispatch 7am-7pm Sunday through Friday, and the estimate is free with no obligation. Whatever brand you have, we know it.
Written by the team at Jasper AC Repair.